Multi-tube dust collector - Model 220

The HXTD multi cyclone dust collector belongs to the cyclone type dust collector. When the dusty gas enters the cyclone guide in parallel in the box, it rotates at high speed in the cyclone cylinder. It is under the action of centrifugal force, dust separation, dust falls in the ash bucket, discharged by the ash valve. The purified gas forms an updraft and is discharged through the outlet of the gas collecting chamber through the exhaust pipe to achieve dust removal effect.

Information

Product Overview

Structure of HXTD Multi Cyclone Dust Collector
Flue gas outlet	Flue gas inlet	Upper body	Ash hopper	Electric ash discharge valve	Cyclone	Observation hole

Multi-cyclone dust collector Multi-tube dust collector

Support

According to the size of dust particle size and dust collection efficiency, we can choose different cyclones to make multi cyclone dust collector, or customize cyclones according to customers' requirements.

Principle of HXTD Multi Cyclone Dust Collector

The HXTD multi cyclone dust collector belongs to the cyclone type dust collector. When the dusty gas enters the cyclone guide in parallel in the box, it rotates at high speed in the cyclone cylinder. It is under the action of centrifugal force, dust separation, dust falls in the ash bucket, discharged by the ash valve. The purified gas forms an updraft and is discharged through the outlet of the gas collecting chamber through the exhaust pipe to achieve dust removal effect.

The HXTD multi cyclone dust collector is suitable for high and low temperature dust produced in power station boilers, industrial boilers, biomass boilers, kilns, hot air furnaces, workshops and other situations. It is especially suitable for pre-dedusting of sintering machine, pulverized coal furnace, circulating fluidized bed furnace, thermal oil furnace, fluidized bed furnace and biomass boiler with high initial concentration.

Industrial cyclone dust collector Multi-cyclone dust collector

Characteristics of HXTD Multi Cyclone Dust Collector

1. Wide range of application, suitable for collection and treatment of all kinds of dry dust;

2. Flexible design, large air volume, site location can be designed separately according to the site conditions;

3. High dust collection efficiency, the efficiency of trapping fine dust with particle size of 5 microns can reach more than 95%;

4. Ceramic cyclone has advantages of high temperature resistance, corrosion resistance, wear resistance, not blocked;

5. Multi cyclone dust collector can be used as flame arrester for biomass boiler, effectively avoiding the loss caused by burning bags on spark;

6. Multi cyclone dust collector has a simple structure and stable operation. Compared with cloth bag and ESP, it has less investment and no operation and maintenance cost.

When the flue gas temperature exceeds 300 degrees or an SCR denitrification device is installed at the back end, the outer surface shall be insulated with 100mm thick aluminum silicate wool felt to prevent heat loss and scalding of workers.
When the flue gas temperature exceeds 300 degrees, the overall equipment needs to consider increasing the thickness of the steel plate, supports and stiffeners, and the strength should be greater than that of ordinary multi - tube equipment at about 150°. If conditions permit, the inlet section of the multi - tube and the flue gas chamber section should be cast with 50mm high - temperature resistant castable.

Multi-tube dust collector Industrial cyclone dust collector

Frequently asked questions	Cause of formation	Terms of settlement
Dust removal efficiency decreased significantly	1. Manual ash relief valve not closed	Check the condition of the discharge valve
	2. Flange joint air leakage	Check flange connections for air leakage and remove air leakage
	3. Check to see if the cyclone is worn or cracked	Replace cyclone

Why Choose Us

Basic Information	Established	1995
	Registered Capital	RMB 68 million
	Annual Output Value	Over RMB 200 million
Scale	Total Employees	150
Scale	Manufacturing Area	35,000 ㎡
Project Experience	Total Engineering Projects	Nearly 500
	Denitrification Systems Delivered	~3,000 units
	Dust Removal Systems Delivered	~10,000 units
	Desulfurization Systems Delivered	~5,000 units
	Wet Electrostatic Systems Delivered	~250 units
Technology	Patents	50+
Market Coverage	Export Regions	Africa, South America, Southeast Asia

Manufacturing & Production Capacity

After-Sales Service

Haina provides on-site installation, commissioning and technical training.Regular follow-up inspections are arranged after project delivery to support long-term operation stability.

Multi-tube dust collector